When a sim is new or it has expired it needs to be provisioned
with the carrier. Basically provisioning is associating a sim with
a user account. When a sim isn't provisioned then operators will
restrict access to the network and only allow certain addresses
or services to be used.
This set of changes allows two types of provisioning networks to be
recognized. The first is a network that causes all DNS lookups to be
redirected to a different address than was intended. This is exemplified
by how T-Mobile works.
The second technique uses a special apn for provisioning. An example is
AT&T where lwaactivate is the provisioning apn and broadband is the
normal apn. We first try broadband and if we are unable to connect we
try lwaactivate. When we see the activate we identify it as special and
the ApnContext.isProvisioningApn will return true.
In the future our plan is to create a new network type that can be added
to the apn list, but for now it identified by name.
Here is a list of significant changes:
- CaptivePortalTracker now only test WiFi networks instead of all networks
- checkMobileProvisioning checks for provisioning networks and doesn't
try to ping.
- IConnectivityManager.aidl changes:
* getProvisioningOrActiveNetworkInfo was added to and used by Manage
mobile plan in WirelessSettings so even when there is no active
network it will still allow provisioning. Otherwise it would report
no internet connection.
* setSignInErrorNotificationVisible is used by both
CaptiviePortalTracker and checkMobileProvisioning so they use the
same code for the notifications.
* checkMobileProvisioning was simplified to have only a timeout as
returning the result is now harder as we abort simultaneous call
otherwise we'd could get into loops because we now check every time
we connect to mobile.
- Enhanced MDST to handle the provisioning network.
- Added CONNECTED_TO_PROVISIONING_NETWORK to NetworkInfo to make a new
state so we don't announce to the world we're connected.
- TelephonyIntents.ACTION_DATA_CONNECTION_CONNECTED_TO_PROVISIONING_APN
is sent by the low level data connection code to notify Connectivity
Service that a provisioning apn has connected. This allows CS to
handle the connection differently than a normal connection.
Bug: 10328264
Change-Id: I3925004011bb1243793c4c1b963d923dc2b00cb5
When the system becomes loaded the PhoneApp can be delayed
significantly and a call to setEnableFailFastMobileData may not
occur because the channel between the MobileDataStateTracker (MDST)
and DcTracker (DCT) is not connected.
Solution: Add a isReady to MDST and isMobileDataStateTrackerReady to
ConnectivityService and call it from isMobileOk.
Bug: 10351868
Change-Id: I92f9d58121b88186b636cd71c2fd2ef9a28f7cf6
Move the early return outside the try {} finally so we don't call
setEnableFailFastMobileData(DctContants.DISABLED). Otherwise
referencing counting is wrong and an exception is thrown in DcTrackerBase.
Bug: 10304904
Change-Id: I5ba5121e473bada9f3daa8d6f3d3577cec8212fc
When captive portal checking completes pass back the result.
This is used to enable/disable failing fast for mobile. When
failing fast is enabled we don't check for data stalls and thus
won't be continually trying to do recovery operations, such as
restarting the radio.
Bug: 9462512
Change-Id: I0dea0eee519f8ee7f94e79d40e82c18f30d7fe2e
I needed to test the result of startUsingNetworkFeature, otherwise
on mobile networks that are slow to come up, we won't detect
warm SIMs after booting.
Bug: 9962943
Change-Id: Ib638a4e43867ecaa85d6abff65643b77a63526b6
After detecting there is a captive portal the url used in the
notification for mobile networks should be updateable via gservices.
These urls will be the same as used by CheckMp and is needed for
carriers that have specific provisioning urls such as AT&T and Verizon.
Bug: 9622647
Change-Id: Idcf4dabc72ece1dbbe1d5e5a21e550dd06fe16c7
Various applications such as Skype and our legacy VPN code
do not understand routes pointed directly at point-to-point
interfaces and require a default gateway IPv4 address in
order to function.
Grudgingly accept that routes without default gateways Are Hard
and use gatewayed routes instead. This causes routing to go from:
default dev clat4 scope link
to:
default via 192.0.0.4 dev clat4 scope link
192.0.0.4 dev clat4 scope link
and those apps now work.
Bug: 9597256
Bug: 9597516
Change-Id: I7b7890873802d3cb99affd6eb70b8ab75e7a2cf6
It used to be set at boot, but that was too quick to pick up carrier
specific resources. With this change even if you switch sims subequent
checks get the new values.
bug:9865616
Change-Id: I8c270c6b02fc6bdd3c3d76ceea58172df25e058d
A simple mechanism for doing this is to take advantage of the fact
that we require the device to reboot after a sim has been changed.
Thus when connectivity service is started we wait to get a connection
then call checkMobileProvisioning once. We also add a check that
the DEVICE_PROVISIONED is true, i.e. SetupWizard has been run.
Bug: 9784024
Change-Id: I5c1936744f6fc55a447ae44cd36eec3849d27e21
The new one is often null when disconnected, so using the new fails.
In other situations, it's the connections on the old network we want
to reset anyway, so the old code when it would work would also do
the wrong thing (unless new iface == old iface).
bug:9112928
Change-Id: I1fcae89cc3aa9d712e516e7c97cece0b89869bd9
To date WiFi only devices were defined by the list of networkAttributes
in config.xml overriden in on a per-device basis. This change is the
simplest change needed to determine this at runtime and therefore allowing
a single build to support the two different configurations.
Bug: 8562845
Change-Id: I34de5c6accc718b199c13815537de1debfe3dc91
VPN used to just watch the interface, but that is insufficient. There
is no promise that the interface will go down when we're done with it.
Now that wifi stays on in scan-only mode despite user turning it off
it seems that the interface is left up, even in AP mode.
Now listening for ConnectivityService broadcast that the network we were on
has disconnected and tearing down the VPN then or when the interface
goes away.
bug:8550083
Change-Id: Icf414497bc55bead69de04e91f39f90ac2e6578a
Fixes issues brought in by change to isHostRoute. isHostRoute
was technically correct, but the callers really wanted hasNextHop
behavior.
bug:8597268
Change-Id: I360761ccfa98b2ba34642f717a78fa71ec1bae4f
The Global http proxy shouldn't be used by apps, but can be useful in certain
conditions.
bug:8264794
bug:8557674
Change-Id: Ia3cbe542e448d9e74d0492626a13e9fd34ad797a
Change our order of operations so that secondary route table
adds succeed. Working to understand the why of this too.
bug:8361314
Change-Id: Ie25061eb38c62eaa5e60aa8a488496de49bdbd9d
Normally, clatd is stopped when a connection disconnects.
However, if the connection's LinkProperties change, or if the
disconnect somehow gets lost (e.g., because of bug 8486114),
then we need to stop it (and possibly restart it).
Bug: 8276725
Change-Id: Ib8ad0d653ed8d0cd70b7414bcaa8fdaef8ba5fcc
Allows the external BT stack the means to communicate with
ConnectivityService during reverse tethering.
bug:8445208
Change-Id: Ice7dfb0b50c9481d359aed14a51372878185171c
1. Add a Nat464Xlat service that ConnectivityService can use
to start and stop clat. When clat is started, the service
waits for the clat interface to come up and then calls
ConnectivityService to add the appropriate routes.
2. Make ConnectivityService start clat when an IPv6-only mobile
interface is connected. We only support clat on mobile for
now.
3. Make tethering use the interface that has the IPv4 default
route insted of using the base interface of the
LinkProperties. This allows us to tether to a stacked
interface, which is needed for tethering with 464xlat.
Bug: 8276725
Change-Id: I24480af69ee280f504399062638af0836a56268e
Currently, ConnectivityService adds and removes routes to/from
the routing table only based on the LinkProperties's routes.
Make it update routes based on the stacked links as well.
Bug: 8276725
Change-Id: I9a2adf537af5a04de0aaab3780afbcc3bb5c6acb
modifyRoute takes both an interface name and a LinkProperties.
This is redundant because all callers get the interface name
from the LinkProperties. Make modifyRoute get the interface
name from the LinkProperties instead.
Change-Id: I41ba8e0a10241c2f1107204fcaca2be74556042b
These checks while technically reasonable are a hard to swallow API change
that may break existing apps and pragmatically serves no purpose: the protected
data is available in publicly readable java VM properties.
Change-Id: I522c493c2604a33e28d99e2be31054326c9a8323
