7adfb2b429
Merge kernel.lnx.5.4-200915 into msm-5.10. Change-Id: If85db2d0b92b484f2e439d72bee8c5e1056baa3f
394 lines
10 KiB
Plaintext
394 lines
10 KiB
Plaintext
#include "holi-audio-overlay.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/linux-event-codes.h>
|
|
#include "holi-pmic-overlay.dtsi"
|
|
#include "holi-thermal-overlay.dtsi"
|
|
#include <dt-bindings/iio/qti_power_supply_iio.h>
|
|
|
|
&sdhc_1 {
|
|
status = "ok";
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc1_on>;
|
|
pinctrl-1 = <&sdc1_off>;
|
|
|
|
vdd-supply = <&L7E>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 570000>;
|
|
|
|
vdd-io-supply = <&L12A>;
|
|
qcom,vdd-io-always-on;
|
|
qcom,vdd-io-lpm-sup;
|
|
qcom,vdd-io-voltage-level = <1800000 1800000>;
|
|
qcom,vdd-io-current-level = <0 325000>;
|
|
};
|
|
|
|
&sdhc_2 {
|
|
status = "ok";
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc2_on>;
|
|
pinctrl-1 = <&sdc2_off>;
|
|
|
|
vdd-supply = <&L9E>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 800000>;
|
|
|
|
vdd-io-supply = <&L6E>;
|
|
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
|
qcom,vdd-io-current-level = <0 22000>;
|
|
|
|
cd-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v3";
|
|
|
|
vdda-phy-supply = <&L18A>;
|
|
vdda-pll-supply = <&L22A>;
|
|
vdda-phy-max-microamp = <62900>;
|
|
vdda-pll-max-microamp = <18300>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
|
vdd-hba-fixed-regulator;
|
|
|
|
vcc-supply = <&L7E>;
|
|
vcc-voltage-level = <2950000 2960000>;
|
|
vcc-max-microamp = <800000>;
|
|
|
|
vccq2-supply = <&L12A>;
|
|
vccq2-max-microamp = <800000>;
|
|
vccq2-voltage-level = <1800000 1800000>;
|
|
|
|
qcom,vddp-ref-clk-supply = <&L22A>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&qupv3_se0_i2c {
|
|
status = "ok";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
nq@28 {
|
|
compatible = "qcom,sn-nci";
|
|
reg = <0x28>;
|
|
qcom,sn-irq = <&tlmm 9 0x00>;
|
|
qcom,sn-ven = <&tlmm 6 0x00>;
|
|
qcom,sn-firm = <&tlmm 8 0x00>;
|
|
qcom,sn-clkreq = <&tlmm 7 0x00>;
|
|
qcom,sn-vdd-1p8-supply = <&L11A>;
|
|
qcom,sn-vdd-1p8-voltage = <1800000 1800000>;
|
|
qcom,sn-vdd-1p8-current = <157000>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <9 0>;
|
|
interrupt-names = "nfc_irq";
|
|
pinctrl-names = "nfc_active", "nfc_suspend";
|
|
pinctrl-0 = <&nfc_int_active &nfc_enable_active>;
|
|
pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend>;
|
|
};
|
|
};
|
|
|
|
&soc {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
label = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&key_vol_up_default>;
|
|
|
|
vol_up {
|
|
label = "volume_up";
|
|
gpios = <&pm6350_gpios 2 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <1>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
gpio-key,wakeup;
|
|
debounce-interval = <15>;
|
|
linux,can-disable;
|
|
};
|
|
};
|
|
|
|
mtp_batterydata: qcom,battery-data {
|
|
qcom,batt-id-range-pct = <15>;
|
|
#include "qg-batterydata-alium-3600mah.dtsi"
|
|
#include "qg-batterydata-atl466271_3300mAh.dtsi"
|
|
#include "qg-batterydata-atl436186020H_3780mAh.dtsi"
|
|
};
|
|
};
|
|
|
|
&pm6150a_amoled {
|
|
status = "ok";
|
|
};
|
|
|
|
&qupv3_se8_i2c {
|
|
status = "okay";
|
|
qcom,i2c-touch-active="synaptics,tcm-i2c";
|
|
|
|
synaptics_tcm@20 {
|
|
compatible = "synaptics,tcm-i2c";
|
|
reg = <0x20>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <22 0x2008>;
|
|
pinctrl-names = "pmx_ts_active","pmx_ts_suspend",
|
|
"pmx_ts_release";
|
|
pinctrl-0 = <&ts_active>;
|
|
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
|
pinctrl-2 = <&pmx_ts_release>;
|
|
vdd-supply = <&L11A>;
|
|
avdd-supply = <&L6A>;
|
|
synaptics,pwr-reg-name = "avdd";
|
|
synaptics,bus-reg-name = "vdd";
|
|
synaptics,irq-gpio = <&tlmm 22 0x2008>;
|
|
synaptics,irq-on-state = <0>;
|
|
synaptics,reset-gpio = <&tlmm 21 0x00>;
|
|
synaptics,reset-on-state = <0>;
|
|
synaptics,reset-active-ms = <20>;
|
|
synaptics,reset-delay-ms = <200>;
|
|
synaptics,power-delay-ms = <200>;
|
|
synaptics,ubl-i2c-addr = <0x20>;
|
|
synaptics,extend_report;
|
|
synaptics,firmware-name = "synaptics_firmware.img";
|
|
|
|
panel = <&dsi_rm69299_visionox_amoled_video
|
|
&dsi_rm69299_visionox_amoled_cmd>;
|
|
};
|
|
};
|
|
|
|
&pm7250b_charger {
|
|
status = "ok";
|
|
#io-channel-cells = <1>;
|
|
io-channels = <&pm7250b_vadc ADC5_USB_IN_V_16>,
|
|
<&pm7250b_vadc ADC5_USB_IN_I>,
|
|
<&pm7250b_vadc ADC5_CHG_TEMP>,
|
|
<&pm7250b_vadc ADC5_DIE_TEMP>,
|
|
<&pm7250b_vadc ADC5_AMUX_THM3_100K_PU>,
|
|
<&pm7250b_vadc ADC5_SBUx>,
|
|
<&pm7250b_vadc ADC5_VPH_PWR>,
|
|
<&pm7250b_vadc ADC5_AMUX_THM1_100K_PU>,
|
|
<&pm7250b_qg PSY_IIO_RESISTANCE_ID>,
|
|
<&pm7250b_qg PSY_IIO_VOLTAGE_NOW>,
|
|
<&pm7250b_qg PSY_IIO_TEMP>,
|
|
<&pm7250b_qg PSY_IIO_CAPACITY>,
|
|
<&pm7250b_qg PSY_IIO_VOLTAGE_OCV>,
|
|
<&pm7250b_qg PSY_IIO_VOLTAGE_AVG>,
|
|
<&pm7250b_qg PSY_IIO_DEBUG_BATTERY>,
|
|
<&pm7250b_qg PSY_IIO_REAL_CAPACITY>,
|
|
<&pm7250b_qg PSY_IIO_CC_SOC>,
|
|
<&pm7250b_qg PSY_IIO_CURRENT_NOW>,
|
|
<&pm7250b_qg PSY_IIO_VOLTAGE_MAX>,
|
|
<&pm7250b_qg PSY_IIO_CHARGE_FULL>,
|
|
<&pm7250b_qg PSY_IIO_CHARGE_COUNTER>,
|
|
<&pm7250b_qg PSY_IIO_CYCLE_COUNT>,
|
|
<&pm7250b_qg PSY_IIO_CHARGE_FULL_DESIGN>,
|
|
<&pm7250b_qg PSY_IIO_TIME_TO_FULL_NOW>,
|
|
<&smb1396_div2_cp_master PSY_IIO_PARALLEL_MODE>,
|
|
<&smb1396_div2_cp_master PSY_IIO_PARALLEL_OUTPUT_MODE>,
|
|
<&smb1396_div2_cp_master PSY_IIO_MIN_ICL>,
|
|
<&smb1396_div2_cp_master PSY_IIO_CP_SWITCHER_EN>,
|
|
<&smb1396_div2_cp_master PSY_IIO_CP_ENABLE>,
|
|
<&smb1396_div2_cp_master PSY_IIO_CP_ILIM>,
|
|
<&smb1396_div2_cp_master PSY_IIO_CP_DIE_TEMP>,
|
|
<&smb1396_div2_cp_slave PSY_IIO_CURRENT_CAPABILITY>;
|
|
io-channel-names = "usb_in_voltage",
|
|
"usb_in_current",
|
|
"chg_temp",
|
|
"die_temp",
|
|
"conn_temp",
|
|
"sbux_res",
|
|
"vph_voltage",
|
|
"skin_temp",
|
|
"resistance_id",
|
|
"voltage_now",
|
|
"temp",
|
|
"capacity",
|
|
"voltage_ocv",
|
|
"voltage_avg",
|
|
"debug_battery",
|
|
"real_capacity",
|
|
"cc_soc",
|
|
"current_now",
|
|
"voltage_max",
|
|
"charge_full",
|
|
"charge_counter",
|
|
"cycle_count",
|
|
"charge_full_design",
|
|
"time_to_full_now",
|
|
"parallel_mode",
|
|
"parallel_output_mode",
|
|
"min_icl",
|
|
"cp_switcher_en",
|
|
"cp_enable",
|
|
"cp_ilim",
|
|
"cp_die_temp",
|
|
"current_capability";
|
|
qcom,battery-data = <&mtp_batterydata>;
|
|
qcom,sec-charger-config = <1>;
|
|
qcom,auto-recharge-soc = <98>;
|
|
qcom,step-charging-enable;
|
|
qcom,sw-jeita-enable;
|
|
qcom,charger-temp-max = <800>;
|
|
qcom,smb-temp-max = <800>;
|
|
qcom,suspend-input-on-debug-batt;
|
|
qcom,fcc-stepping-enable;
|
|
qcom,fcc-step-delay-ms = <100>;
|
|
qcom,fcc-step-size-ua = <100000>;
|
|
qcom,smb-internal-pull-kohm = <0>;
|
|
qcom,en-skin-therm-mitigation;
|
|
qcom,hvdcp3-standalone-config;
|
|
};
|
|
|
|
&pm7250b_qg {
|
|
status = "ok";
|
|
#io-channel-cells = <1>;
|
|
io-channels = <&pm7250b_vadc ADC5_BAT_THERM_100K_PU>,
|
|
<&pm7250b_vadc ADC5_BAT_ID_100K_PU>,
|
|
<&pm7250b_charger PSY_IIO_INPUT_CURRENT_LIMITED>,
|
|
<&pm7250b_charger PSY_IIO_RECHARGE_SOC>,
|
|
<&pm7250b_charger PSY_IIO_FORCE_RECHARGE>,
|
|
<&pm7250b_charger PSY_IIO_CHARGE_DONE>,
|
|
<&smb1396_div2_cp_master PSY_IIO_CP_ENABLE>;
|
|
io-channel-names = "batt-therm",
|
|
"batt-id",
|
|
"input_current_limited",
|
|
"recharge_soc",
|
|
"force_recharge",
|
|
"charge_done",
|
|
"cp_charging_enabled";
|
|
qcom,battery-data = <&mtp_batterydata>;
|
|
qcom,qg-iterm-ma = <150>;
|
|
qcom,hold-soc-while-full;
|
|
qcom,linearize-soc;
|
|
qcom,cl-feedback-on;
|
|
qcom,tcss-enable;
|
|
qcom,fvss-enable;
|
|
qcom,fvss-vbatt-mv = <3300>;
|
|
qcom,bass-enable;
|
|
qcom,use-cp-iin-sns;
|
|
};
|
|
|
|
&pm7250b_vadc {
|
|
smb1390_therm@e {
|
|
qcom,scale-fn-type = <ADC_SCALE_HW_CALIB_PM5_SMB1398_TEMP>;
|
|
};
|
|
};
|
|
|
|
&pm7250b_gpios {
|
|
smb_stat {
|
|
smb_stat_default: smb_stat_default {
|
|
pins = "gpio6";
|
|
function = "normal";
|
|
input-enable;
|
|
bias-pull-up;
|
|
qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
|
|
power-source = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qupv3_se10_i2c {
|
|
qcom,clk-freq-out = <100000>;
|
|
status = "ok";
|
|
#include "smb1398.dtsi"
|
|
};
|
|
|
|
&smb1396 {
|
|
interrupts = <0x2 0xc5 0x0 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-parent = <&spmi_bus>;
|
|
interrupt-names = "smb1396";
|
|
pinctrl-names = "default";
|
|
qcom,enable-toggle-stat;
|
|
pinctrl-0 = <&smb_stat_default>;
|
|
status = "ok";
|
|
};
|
|
|
|
&smb1396_div2_cp_master {
|
|
io-channels = <&smb1396_div2_cp_slave PSY_IIO_CURRENT_CAPABILITY>,
|
|
<&smb1396_div2_cp_slave PSY_IIO_CP_ENABLE>,
|
|
<&smb1396_div2_cp_slave PSY_IIO_CP_INPUT_CURRENT_MAX>,
|
|
<&pm7250b_vadc ADC5_AMUX_THM2>,
|
|
<&pm7250b_charger PSY_IIO_USB_REAL_TYPE>,
|
|
<&pm7250b_charger PSY_IIO_ADAPTER_CC_MODE>,
|
|
<&pm7250b_charger PSY_IIO_PD_CURRENT_MAX>,
|
|
<&pm7250b_charger PSY_IIO_USB_INPUT_CURRENT_SETTLED>,
|
|
<&pm7250b_charger PSY_IIO_SMB_EN_MODE>,
|
|
<&pm7250b_charger PSY_IIO_SMB_EN_REASON>;
|
|
io-channel-names = "current_capability",
|
|
"cp_enable",
|
|
"cp_input_current_max",
|
|
"die_temp",
|
|
"real_type",
|
|
"adapter_cc_mode",
|
|
"pd_current_max",
|
|
"input_current_settled",
|
|
"smb_en_mode",
|
|
"smb_en_reason";
|
|
qcom,parallel-input-mode = <1>; /* USBIN */
|
|
qcom,parallel-output-mode = <2>; /* VBAT */
|
|
status = "ok";
|
|
};
|
|
|
|
&smb1396_slave {
|
|
status = "ok";
|
|
};
|
|
|
|
&smb1396_div2_cp_slave {
|
|
status = "ok";
|
|
};
|
|
|
|
|
|
&pm7250b_charger {
|
|
dpdm-supply = <&qusb_phy0>;
|
|
|
|
smb5_vbus: qcom,smb5-vbus {
|
|
regulator-name = "smb5-vbus";
|
|
};
|
|
|
|
smb5_vconn: qcom,smb5-vconn {
|
|
regulator-name = "smb5-vconn";
|
|
};
|
|
};
|
|
|
|
&pm7250b_pdphy {
|
|
vdd-pdphy-supply = <&L3A>;
|
|
vbus-supply = <&smb5_vbus>;
|
|
vconn-supply = <&smb5_vconn>;
|
|
|
|
#io-channel-cells = <1>;
|
|
io-channels = <&pm7250b_charger PSY_IIO_PD_ACTIVE>,
|
|
<&pm7250b_charger PSY_IIO_TYPEC_CC_ORIENTATION>,
|
|
<&pm7250b_charger PSY_IIO_CONNECTOR_TYPE>,
|
|
<&pm7250b_charger PSY_IIO_TYPEC_POWER_ROLE>,
|
|
<&pm7250b_charger PSY_IIO_PD_USB_SUSPEND_SUPPORTED>,
|
|
<&pm7250b_charger PSY_IIO_TYPEC_SRC_RP>,
|
|
<&pm7250b_charger PSY_IIO_PD_IN_HARD_RESET>,
|
|
<&pm7250b_charger PSY_IIO_PD_CURRENT_MAX>,
|
|
<&pm7250b_charger PSY_IIO_PR_SWAP>,
|
|
<&pm7250b_charger PSY_IIO_PD_VOLTAGE_MIN>,
|
|
<&pm7250b_charger PSY_IIO_PD_VOLTAGE_MAX>,
|
|
<&pm7250b_charger PSY_IIO_USB_REAL_TYPE>,
|
|
<&pm7250b_charger PSY_IIO_TYPEC_MODE>,
|
|
<&pm7250b_charger PSY_IIO_PE_START>;
|
|
io-channel-names = "pd_active",
|
|
"typec_cc_orientation",
|
|
"connector_type",
|
|
"typec_power_role",
|
|
"pd_usb_suspend_supported",
|
|
"typec_src_rp",
|
|
"pd_in_hard_reset",
|
|
"pr_current_max",
|
|
"pr_swap",
|
|
"pd_voltage_min",
|
|
"pd_voltage_max",
|
|
"real_type",
|
|
"typec_mode",
|
|
"pe_start";
|
|
};
|
|
|
|
&usb0 {
|
|
extcon = <&pm7250b_pdphy>, <&eud>;
|
|
};
|